321 Studiosr 9356130 User Manual

User’s guide  
Issue 1  
9356130  
 
For your safety  
Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information  
is given in this user’s guide.  
Do not switch the camera on when wireless phone use is prohibited or when it may cause  
interference or danger.  
ROAD SAFETY COMES FIRST Don't install the camera in a vehicle. Do not use the camera or your  
mobile phone to control or configure the camera while driving; park the vehicle first.  
INTERFERENCE All wireless devices may get interference, which could affect performance.  
SWITCH OFF IN HOSPITALS Follow any regulations and rules. Switch the camera off near medical  
equipment.  
SWITCH OFF IN AIRCRAFT Wireless devices can cause interference in aircraft.  
SWITCH OFF WHEN REFUELLING Don't use the camera at a refuelling point. Don't use near fuel or  
chemicals.  
SWITCH OFF NEAR BLASTING Don't use the camera where blasting is in progress. Observe  
restrictions, and follow any regulations or rules.  
USE SENSIBLY Use only in the normal operating positions. Don't touch the antenna unnecessarily.  
QUALIFIED SERVICE Only qualified personnel may install or repair equipment.  
ENHANCEMENTS AND BATTERIES Use only approved enhancements and batteries. Do not connect  
incompatible products.  
Copyright©2003 Nokia. All rights reserved.  
 
 
BACKUP COPIES Remember to make backup copies of all important data.  
CONNECTING TO OTHER DEVICES When connecting to any other device, read its user's guide for  
detailed safety instructions. Do not connect incompatible products.  
WATER-RESISTANCE Your camera is not water-resistant. Keep it dry.  
Copyright©2003 Nokia. All rights reserved.  
 
Contents  
Introduction..................................................................................1  
Getting started.............................................................................3  
Installing the camera ............................................................................................................... 5  
Installing the PC Suite software ........................................................................................... 8  
Configuring the settings with PC Suite .............................................................................. 9  
Main page ...........................................................................................................................10  
Settings page......................................................................................................................11  
Users page...........................................................................................................................15  
Monitor page......................................................................................................................17  
Security settings................................................................................................................17  
Saving the PC Suite settings..........................................................................................18  
Configuring the settings with SMS ...................................................................................18  
Taking the camera in use with SMS commands ......................................................19  
Light indicators ........................................................................................................................26  
Using the camera ...................................................................... 29  
Capturing an image ................................................................................................................29  
Using motion detection ........................................................................................................30  
Using timed imaging ..............................................................................................................31  
Using the thermometer .........................................................................................................32  
Using the audio connection .................................................................................................32  
Copyright©2003 Nokia. All rights reserved.  
 
Care and maintenance.............................................................. 33  
Important safety information.................................................. 35  
Technical specifications............................................................ 38  
Copyright©2003 Nokia. All rights reserved.  
 
Introduction  
The Nokia Observation Camera is a remote imaging device with a motion detector, thermometer, and  
microphone. With the camera you can capture images remotely and send them to your multimedia  
messaging (MMS) enabled mobile phone with a colour display, or to an e-mail address. You can control  
and configure the camera with short messages (SMS), and the PC Suite for Nokia Observation Camera  
software is provided for more advanced functions.  
Note: National laws and regulations may place restrictions on recording images and regarding  
further processing and use of such data. Do not use this feature illegally. Honour the privacy  
and other legitimate rights of others and obey all laws governing, for example, data protection,  
privacy, and publicity.  
Note: The images and messages sent from the camera will be charged to the subscription of the  
SIM card in the camera.  
The Nokia Observation Camera is approved for use on the GSM 900/1800 network.  
To use the Nokia Observation Camera, you need:  
• a GPRS enabled mobile subscription with a SIM card and MMS service.  
• an MMS and SMS enabled mobile phone with a colour display  
• GSM network coverage in the camera premises  
• an available e-mail address if you want to receive images to your e-mail.  
Note: Check how large MMS messages your mobile phone is capable of receiving. Your network  
operator may also restrict the size of MMS messages. Ask your network operator for details.  
1
Copyright©2003 Nokia. All rights reserved.  
 
 
Before you can use any of these network services, you must subscribe to them through your service  
provider and obtain instructions for their use from your service provider.  
Note: Some networks may not support all language-dependent characters and/or services.  
Note: For availability, rates, and information on using SIM services, contact your SIM card  
vendor, e.g. network operator, service provider, or other vendor.  
Note: The MMS function can be used only if it is supported by your network operator or service  
provider. Only devices that offer compatible multimedia message or e-mail features can receive  
and display multimedia messages.  
Important: Multimedia message objects may contain viruses or otherwise be harmful to your  
phone or PC. Do not open any attachment if you are not sure of the trustworthiness of the  
sender.  
The default setting of the multimedia message service is on ("Allow multimedia reception" is set  
"Yes"), and your operator or service provider may charge you for every message you receive.  
Warning: Use only power source ACW-6 and enhancements approved by the camera  
manufacturer for use with this particular camera model. The use of any other types may  
invalidate any approval or warranty applying to the camera, and may be dangerous.  
For availability of approved enhancements, please check with your dealer.  
When you disconnect the power cord of any enhancement, grasp and pull the plug, not the cord.  
Warning: Do not switch the camera on when wireless phone use is prohibited or when it may  
cause interference or danger.  
Warning: In order to comply with RF exposure requirements for mobile transmitting devices, a  
minimum distance of 20 cm must be maintained between the camera and all persons.  
2
Copyright©2003 Nokia. All rights reserved.  
 
Getting started  
The Nokia Observation Camera sales package contains the following items:  
• Nokia Observation Camera  
• desktop/wall stand  
• mounting screws and a tool for tightening them  
• serial data cable  
• power source and wall mount cradle  
• CD-ROM with PC Suite software  
• user’s guide  
The front panel of the Nokia Observation Camera features:  
• Infrared light source for capturing images in low light (1)  
• Start button for motion detection (2)  
• Motion detector (3)  
3
Copyright©2003 Nokia. All rights reserved.  
 
 
Figure 1  
The back panel of the Nokia Observation Camera features:  
• SIM card slot (4)  
• Data connector (5)  
• External antenna connector (6)  
• Power connector (7)  
• Thermometer (8)  
4
Copyright©2003 Nokia. All rights reserved.  
 
 
Figure 2  
Installing the camera  
1. Lift up the back lid of the camera and insert a SIM card as shown in Figure 3.  
Figure 3  
5
Copyright©2003 Nokia. All rights reserved.  
 
     
Note: Keep all miniature SIM cards out of the reach of small children.  
Note: If you want to configure the Nokia Observation Camera settings with SMS messages,  
disable the PIN code request on your SIM card before inserting it into the camera. If the PIN  
code request is active, you can only configure the camera settings with PC Suite.  
2. If you configure the camera settings with PC Suite, connect the serial data cable to the data  
connector at the back of the camera and to the COM port of a compatible PC.  
3. Attach the power source to the power connector of the camera and plug it into a mains outlet. If  
the LEDs on the camera light up, the camera receives power from the mains outlet.  
4. Configure the camera settings either with PC Suite or with SMS commands, see Configuring the  
settings with PC Suite on page 9 and Configuring the settings with SMS on page 18.  
5. After completing the configuration, disconnect the serial data cable, and power off the camera by  
unplugging it from the mains outlet.  
6. Attach the camera to the desktop stand with the screw, turn the stand to the usage position and  
tighten the screw with the tool included in the sales package. To tighten the ball joint, remove the  
rubber shield and tighten the screw. See Figure 4.  
6
Copyright©2003 Nokia. All rights reserved.  
 
Figure 4  
You can also mount the stand on a wall: remove the rubber screw shields from the desktop stand  
and attach it to the wall with two screws. Use the wall mount cradle to hold the power source. See  
Figure 5.  
7
Copyright©2003 Nokia. All rights reserved.  
 
Figure 5  
7. Power on the camera.  
Note: When you disconnect the power cord, grasp and pull the plug, not the cord.  
Tip: You can also place the camera on a standard camera tripod.  
Installing the PC Suite software  
Note: PC Suite for Nokia Observation Camera supports the Windows 98/2000/NT/XP operating  
systems and requires 5 MB of free disk space.  
1. Exit all Windows programs. Insert the CD-ROM into the CD-ROM drive of your computer.  
8
Copyright©2003 Nokia. All rights reserved.  
 
 
2. If the CD-ROM is not launched automatically, go to your CD-ROM drive (e.g. drive D) and double-  
click Setup.exe.  
3. Select the language for the installation program and software.  
4. The Welcome page of the installation wizard opens. Click Next to continue.  
5. Read through the Nokia license agreement. If you do not accept the license agreement, click No,  
in which case you cannot use the software and the installation procedure stops. Click Yes to accept  
the license agreement.  
6. Enter your name and the name of your company. Click Next.  
7. Select the destination folder for the software. The default folder is C:\Program Files\Nokia\Nokia  
Observation Camera. If you want to install the software in another drive or folder, click Browse.  
When you have selected the correct destination folder, click Next.  
8. Select the program folder for the software and click Next.  
9. Check the installation settings. To accept them, click Next. To change the settings, click Back, make  
the changes, and then click Next. The installation program starts copying the files.  
10.The Completion page informs you when the installation is completed. Remove the CD-ROM from  
the CD-ROM drive and click Finish. You may need to restart your computer.  
Configuring the settings with PC Suite  
With the PC Suite for Nokia Observation Camera software you can configure all the necessary settings  
for your camera.  
9
Copyright©2003 Nokia. All rights reserved.  
 
 
The user interface of the software consists of four pages: Main, Settings, Users, and Monitor. You can  
open the pages by clicking the icons on the icon bar on the left.  
Note: If you do not have a compatible PC available, you can configure the camera settings with  
your mobile phone using SMS messages. See Configuring the settings with SMS on page 18.  
1. To access PC Suite, go to Start, select Programs, and select Nokia Observation Camera.  
2. Plug the serial data cable into the data connector of the Nokia Observation Camera and the COM  
port of your PC. You can configure the correct COM port in the File, COM Port Settings menu.  
3. When the PC is connected to the camera, you are asked for your security code. The preset code is  
1234. Change the preset code in the Security settings, Change access codes menu. Keep the new  
code secret and in a safe place separate from the camera.  
Note: Only those who know the security code can change the camera settings and give new  
users access to camera functions.  
4. If the PIN code request is active on your SIM card, you will be prompted to enter the PIN code of  
your SIM card.  
5. When PC Suite asks whether you want to import the camera settings to PC Suite, click Yes.  
Note: Before you can use the camera, you need to configure the name and the language of the  
camera (see page 11), the master user (see page 15), and the connection used (see page 14).  
Main page  
The Main page shows general information about the camera. You can also check the current settings  
of the camera and save them to a file on your PC.  
10  
Copyright©2003 Nokia. All rights reserved.  
 
 
Import: click this button to import the current settings from the camera to PC Suite.  
Write: save the current settings to the camera.  
Open: open a settings file from your PC.  
Save as: save the current settings to your PC.  
Settings page  
The Settings page consists of four tabs, each of which contains a group of settings.  
General settings tab  
Camera name: give a name for the camera. The name can be up to 20 characters long and it must not  
contain spaces or special characters.  
Language: select the language for the SMS commands and notifications.  
Send SMS after power out: check this box if you want the camera to send you an SMS message when  
a power shortage has occurred and the power is back on.  
Note: This feature can only be used when motion detection is on.  
Note: The messages sent from the camera will be charged to the subscription of the SIM card  
in the camera.  
Resolution: select whether you want to receive the images in high (640 x 480 pixels), normal (320 x  
240 pixels), or compact (160 x 120 pixels) resolution.  
Image quality: select whether you want the images to be of high, normal, or basic quality.  
11  
Copyright©2003 Nokia. All rights reserved.  
 
   
Camera position: If the camera is placed in an upright position, select Normal. If the camera is  
mounted upside down, for example on a ceiling, select Upside down. With this setting you can ensure  
that the images captured by the camera are not sent upside down.  
When you have made the necessary changes, click Apply to use the new settings.  
To use the pre-configured factory values for all the camera settings, click the Restore button.  
Automatic imaging tab  
Motion detection: check this box if you want the camera to send you images when it detects motion  
in its coverage area. For more information, see Using motion detection on page 30.  
Send SMS when motion detected: check this box if you want the camera to send you a notification  
immediately when it has detected motion.  
Send SMS after last detection: check this box if you want the camera to send you an SMS message  
after it has sent you all the defined motion detection images (see below) and has stopped detecting  
motion.  
Image sending delay after detection: set the period after which the camera sends you an image  
message when it has captured a motion detection image.  
Number of detections: set how many motion detection image messages (0-10) you want the camera  
to send you before turning off the motion detection function. If you set 0 as the number of image  
messages, motion detection remains on until you turn it off.  
Note: A motion detection image message can contain several images captured at 0.5 second  
intervals. See below.  
Number of images per detected motion: set how many images (1-3) you want the camera to send in  
each motion detection image message.  
12  
Copyright©2003 Nokia. All rights reserved.  
 
 
Note: If you set the resolution of images to High on the General settings tab, you can only  
receive one motion detection image in a message. If you set the resolution to Normal, you can  
receive two images. If you set the resolution to Compact, you can receive three images.  
Timed imaging: check this box if you want the camera to send you images at certain intervals.  
Interval for image sending: set the interval for sending timed images.  
Number of sent images: set the number of images (0-10) to be captured using timed imaging before  
the timed imaging function is turned off. If you set 0 as the number of images, timed imaging remains  
on until you turn it off.  
When you have made the necessary changes, click Apply to use the new settings.  
Thermometer tab  
Note: Turn the thermometer up before using it. Do not use force. See Figure 2 on page 5.  
Scale: select whether to use Celsius or Fahrenheit as the temperature scale.  
Read temperature: click this button to check the current temperature in the camera premises.  
Temperature limits: set the minimum and maximum limits for the temperature. You can then set the  
camera to send you a notification when either of the limits has been reached. See below.  
Send SMS when limit reached: you can set the camera to send you an SMS notification when the  
minimum or the maximum temperature is reached.  
Note: After the camera has sent you a notification on the reached temperature, you need to set  
the temperature limits again, if you want to continue using this function.  
13  
Copyright©2003 Nokia. All rights reserved.  
 
 
Include temperature value with images: check this box if you want the camera to attach the current  
temperature to each image message.  
When you have made the necessary changes, click Apply to use the new settings.  
Connection tab  
Tip: The easiest way to make the necessary configurations is to ask your service provider to send  
you the settings over the air. Click Get at the bottom of the tab, if your service provider has  
enabled this service. You only need to give the number of the MMS settings service, write the  
SMS configuration request message, and click Send.  
GPRS access point name: enter the name of the GPRS access point. Ask your service provider for  
details.  
Home page address: enter the URL address of your MMS centre. Ask your service provider for details.  
User name: enter your user name for the connection. You get the user name from your service provider.  
Password: enter your password for the connection. You get the password from your service provider.  
Gateway IP address: enter the IP address of the WAP gateway. Ask your service provider for details.  
SMSC number: enter the number of your short message centre. Ask your service provider for details.  
Prompt password: check this box if you want the camera to prompt for your password when making  
a connection. Your service provider may require using this feature.  
Connection security: check this box if you want to use a secure connection. Your service provider may  
require using this feature.  
Authentication: select whether to use normal or secure authentication. Ask your service provider for  
details.  
14  
Copyright©2003 Nokia. All rights reserved.  
 
 
Session mode: select whether to use permanent or temporary sessions when using GPRS. Ask your  
service provider for details.  
When you have made the necessary changes, click Apply to use the new settings.  
Users page  
Up to 20 users can use the Nokia Observation Camera. One user is the master user who is allowed to  
configure the settings for the camera.  
The camera authenticates the users by their mobile phone numbers. Requests from phone numbers  
unknown to the camera are ignored.  
Note: The images and SMS notifications sent from the camera will be charged to the  
subscription of the SIM card in the camera.  
Name: enter the name of the user. The name can be up to 20 characters long and it must not contain  
spaces or special characters.  
Master user: check this box if you want this user to be the master user.  
Note: There can be only one master user at a time. The master user is the only one with  
permission to configure the camera with SMS messages. Other users can only take images and  
use the audio connection with SMS. See Configuring the settings with SMS on page 18.  
Phone number: the phone number of the user.  
E-mail address: the e-mail address of the user.  
Send SMS notification about: check the Motion detection box if you want the user to be notified when  
motion has been detected. Check the Temperature limits box if you want the user to be notified when  
15  
Copyright©2003 Nokia. All rights reserved.  
 
   
the temperature limits are reached. Check the Power failure box if you want the user to be notified  
when a power shortage has occurred and the power is back on.  
Note: The Power failure option can only be used when motion detection is on.  
Default image address: select whether to send the images to the user’s mobile phone or e-mail address.  
Allow image request: check this box if you let the user capture images.  
Allow audio connection: check this box if you let the user listen to the premises of the camera.  
Allow timed imaging: check this box if you let the user receive images captured using timed imaging.  
Allow motion detection: check this box if you let the user to receive images captured with motion  
detection.  
Click Add to include the created user to the user list. To remove a user, select the user from the user  
list and click Remove. To update a user’s settings, select the user and click Update.  
Disable image request authentication: check this box if you want to let everyone capture images  
without authentication.  
Warning: If you check the Disable image request authentication box, everyone who knows the  
camera’s phone number can capture images with the camera.  
When you have added all the desired users to the user list, click Apply to import the user list to the  
camera.  
Note: When you click Apply, the current user list of the camera is overwritten. If you want to  
add a user to the current user list, go to the Main page and click Import to open the current  
user list. Then edit the list on the Users page and click Apply.  
16  
Copyright©2003 Nokia. All rights reserved.  
 
Monitor page  
On the Monitor page you can view and capture images.  
Open: click this button to open a previously saved image.  
Save: click this button to save the still image on the monitor.  
Send: click this button to send an image as an MMS message to a recipient.  
Capture image: click this button to capture an image and show it on the monitor.  
Automatic update: select this option to see a continuously updated image from the camera.  
Snapshot: select this option to see still images from the camera.  
Operator: shows the name of your network operator.  
Signal strength: shows the signal strength of the network connection.  
Security settings  
To set the security settings for the Nokia Observation Camera, open the Security settings menu from  
the menu bar.  
PIN code settings: if you set the PIN mode On, the camera asks you to enter your PIN code in PC Suite  
the first time you turn the camera on. The camera then saves the PIN code in its memory and later  
enters the PIN code automatically every time it is turned on. If you set the PIN mode Off, the camera  
does not ask for the PIN code.  
Change access codes: select whether to change the PIN, PIN2, or the Security code. Enter the old code,  
then the new code, and confirm the new code.  
17  
Copyright©2003 Nokia. All rights reserved.  
 
   
Enter security code: type the security code for the camera. The preset code is 1234. Change the preset  
code in Security settings, Change access codes menu. Keep the new code secret and in a safe place  
separate from the camera.  
Saving the PC Suite settings  
You can save the camera settings in a *.noc file. Open the File menu and select Save or Save as. Choose  
the location for the file and enter a name for the file. Click Save.  
When you want to use the saved settings, open the File menu and select Open settings file. Select the  
file and click Open.  
Configuring the settings with SMS  
The Nokia Observation Camera can also be configured with SMS commands.  
Note: The master user is the only one with permission to configure the camera with SMS  
commands. For defining the master user, see the User commands table on page 24.  
When using SMS commands, remember these guidelines:  
• Separate the command and the value with a space. The space is marked in the tables below with  
an underline character (_).  
• If you send several commands in one message, separate the commands with a comma.  
• To check the current value of a setting, send the message: command number, space, question  
mark. For example: 46 ?  
18  
Copyright©2003 Nokia. All rights reserved.  
 
   
• When selecting a setting, you can use the following parameters: on, 1, or +.  
• When removing the selection for a setting, you can use the following parameters: off, 0, or -.  
• The default values of the settings are marked in the tables in bold.  
When you send a command to the camera, the camera replies with a confirmation message.  
Taking the camera in use with SMS commands  
1. Set the language for the camera by sending the SMS command 21_security code_number of  
language to the camera. The preset security code is 1234. The number of your language can be  
found in the General commands table below.  
2. Set yourself as the master user of the camera by sending the SMS command 8_security code_user  
name_phone number to the camera. Replace user name with your name. The name can be up to 20  
characters long and it must not contain spaces or special characters. Replace phone number with  
the number of your mobile phone.  
3. Set the name for the camera by sending the SMS command 25_camera name to the camera.  
Replace camera name with the name you want to give to the camera.  
4. If your service provider supports over-the-air MMS configuration, send the message 91_service  
number_service provider dependent text to the camera. Ask your service provider for the service  
number and text. If your service provider does not support this feature, send the commands listed  
in the Connection commands table to the camera. Ask your service provider for details.  
19  
Copyright©2003 Nokia. All rights reserved.  
 
 
General commands  
Task  
SMS command  
Set the language of the SMS commands and  
notifications. The language numbers are:  
Danish 1, Dutch 2, English 3, Finnish 4, French  
5, German 6, Italian 7, Norwegian 8, Polish 9,  
Portuguese 10, Spanish 11, Swedish 12,  
Simplified Chinese 13, Traditional Chinese  
(Hong Kong) 14, Traditional Chinese (Taiwan)  
15, Czech 16, Canadian French 17, Greek 18,  
Hungarian 19, Brazilian Portuguese 20, Russian  
21, Latin Spanish 22, Thai 23  
21_security code _number of language  
Set a name for the camera  
25_camera name  
Define the position of the camera: normal (1), 19_number  
upside down (2)  
Set the image resolution to high (1), normal (2), 11_number  
or compact (3)  
Capture an image and send it to your mobile  
phone  
1
or  
image  
Capture an image and send it to another phone 1_phone number/e-mail address  
number or e-mail address  
or  
image_phone number/e-mail address  
20  
Copyright©2003 Nokia. All rights reserved.  
 
Task  
SMS command  
Ask for the IMEI code, and software and  
hardware versions of the camera  
92  
Set the SMS notification of power cuts on or off 18_on/off  
Set confirmation messages from the camera on 26_on/off  
or off  
Check the current settings  
Restore factory settings  
77  
99_security code  
Automatic imaging commands  
Task  
SMS command  
Set motion detection on and set how many  
image messages (0-10) you want the camera to  
send after it has detected motion. If you set 0 as  
the number of image messages, motion  
2_on_number of messages  
or  
detection_on_number of messages  
detection remains on until you turn it off  
Set motion detection off  
2_off  
or  
detection_off  
Set the number (1-3) of images in one motion 12_number  
detection image message  
Set motion detection notification on or off  
16_on/off  
21  
Copyright©2003 Nokia. All rights reserved.  
 
Task  
SMS command  
Set the SMS notification on completed motion 17_on/off  
detection on or off  
Set timed imaging on, and define the interval 4_on_hh:mm_number  
and the maximum number (0-10) of timed  
images. If you set 0 as the number of images,  
timed imaging remains on until you turn it off  
or  
timed_on_hh:mm_number  
Set timed imaging off  
4_off  
or  
timed_off  
Thermometer commands  
Task  
SMS command  
Select whether to use Celsius (1) or Fahrenheit 14_number  
(2) as the temperature scale  
Request the current temperature  
3
or  
temp  
Set the temperature alarm on and set the  
temperature limits  
15_on_minimum value_maximum  
value  
Set the temperature alarm off  
15_off  
22  
Copyright©2003 Nokia. All rights reserved.  
 
Task  
SMS command  
Set the sending of current temperature with  
13_on/off  
images on or off  
Connection commands  
Task  
SMS command  
Request over-the-air configurations from your 91_service number_service provider  
service provider  
dependent text  
Set the GPRS access point name  
31_access point name  
Set the address of the MMS centre home page 32_URL address  
Set the user name for the connection  
Set the password for the connection  
Set password prompting on or off  
Set the gateway IP address  
41_user name  
42_password  
43_on/off  
33_IP address  
27_number  
Set the SMS centre number  
Select normal (1) or secure (2) authentication 44_number  
for the connection  
Set connection security on or off  
45_on/off  
Select the permanent (1) or temporary (2)  
session mode  
46_number  
23  
Copyright©2003 Nokia. All rights reserved.  
 
User commands  
Task  
SMS command  
Define the master user. The e-mail address is 8_security code_user name_phone  
not mandatory  
number_e-mail address  
or  
master_security code_user  
name_phone number_e-mail address  
Set the default image address for the master 9_security code_number  
user: mobile phone (1) or e-mail (2)  
or  
address_security code_number  
Add a new user, and give the right to capture 5_security code_user name_user’s  
images and/or use the audio connection  
phone number_on_on  
or  
add_security code_user name_user’s  
phone number_on_on  
Remove a user. The user can be removed based 6_security code_user name/phone  
on either the user name or the phone number number  
or  
remove_security code_user name/  
phone number  
24  
Copyright©2003 Nokia. All rights reserved.  
 
 
Task  
SMS command  
Remove several users  
6_security code_user name 1/phone  
number 1_user name 2/phone number  
2
or  
remove_security code__user name 1/  
phone number 1_user name 2/phone  
number 2  
Check the current user list  
7_security code  
Set image request authentication on. The  
camera authenticates the users by their mobile  
phone numbers. Requests from phone numbers  
unknown to the camera are ignored  
88_security code_on  
Set image request authentication off. Everyone 88_security code_off  
who knows the camera’s phone number can  
capture images with the camera  
Security commands  
Task  
SMS command  
Set the PIN code request on or off  
Change the PIN code  
Change the security code  
22_PIN code_on/off  
23_old PIN code_new code_new code  
24_old code_new code_new code  
25  
Copyright©2003 Nokia. All rights reserved.  
 
Light indicators  
The Nokia Observation Camera has three light indicators (LEDs), which indicate, for example, the  
network status. See Figure 6.  
Figure 6  
Start-up LEDs  
LED 1  
LED 2  
LED 3  
Description  
Red and green Red and green Red and green There is no SIM card in the camera or  
blink  
blink  
blink  
the SIM card is incorrectly inserted  
Green scan  
Green scan  
Green scan  
The camera is connecting to a GSM  
network  
-
-
Red blink  
Red blink  
-
Enter the PIN code in PC Suite  
Enter the PUK code in PC Suite  
Red blink  
26  
Copyright©2003 Nokia. All rights reserved.  
 
   
LED 1  
LED 2  
LED 3  
Description  
Red blink  
Red blink  
Red blink  
Failure, contact service  
Signal strength LEDs  
LED 1  
LED 2  
LED 3  
Signal strength  
No connection  
No connection  
Red blink  
Green blink  
Green  
-
-
-
-
-
-
The signal strength of the network is  
weak  
Green  
Green  
Green  
Green  
Green blink  
Green  
-
The signal strength of the network is  
weak  
-
The signal strength of the network is  
moderate  
Green  
Green blink  
Green  
The signal strength of the network is  
moderate  
Green  
The signal strength of the network is  
strong  
27  
Copyright©2003 Nokia. All rights reserved.  
 
Operating LEDs  
LED 1  
LED 2  
LED 3  
Description  
-
-
Green  
The camera is connected to a GSM  
network  
Green/Red  
Green  
-
-
Green blink  
Green  
The microphone is active  
The camera is in normal operating  
mode  
Red  
-
Green  
Green  
Motion detection is on  
Green  
Red  
Image sending is in progress  
28  
Copyright©2003 Nokia. All rights reserved.  
 
Using the camera  
When you have made all the necessary settings to the Nokia Observation Camera, take it to the place  
of usage, and power up the camera by plugging the power cord to a mains outlet.  
Capturing an image  
To capture an image and have it sent to your mobile phone, send the SMS command 1 to the Nokia  
Observation Camera.  
To capture an image and have it sent to another mobile phone, send the SMS command 1 phone  
number to the Nokia Observation Camera (replace phone number with the desired mobile phone  
number).  
To capture an image and have it sent to an e-mail address, send the SMS command 1 e-mail address  
to the Nokia Observation Camera (replace e-mail address with the desired e-mail address).  
Tip: If you want to add a message to the image, write the message to the end of the SMS  
command in quotation marks. For example: 1 [email protected] “This is my new car!”.  
Note: National laws and regulations may place restrictions on recording images and regarding  
further processing and use of such data. Do not use this feature illegally. Honour the privacy  
and other legitimate rights of others and obey all laws governing, for example, data protection,  
privacy, and publicity.  
29  
Copyright©2003 Nokia. All rights reserved.  
 
   
Using motion detection  
To start motion detection, press the motion detection button on the camera (see Figure 1 on page 4).  
Note: You have 60 seconds to leave the premises before motion detection starts.  
You can also start motion detection by sending the SMS command 2 on [number of image messages  
(0-10)] to the Nokia Observation Camera (replace [number of image messages (0-10)] with the number  
of motion detection image messages you want the camera to send you), or you can configure the  
camera with PC Suite.  
Note: If you set 0 as the number of image messages, motion detection remains on until you turn  
it off.  
When motion detection is on, LED 1 of the camera is red. See Light indicators on page 26. When the  
camera detects motion in the coverage area, it captures images and sends the number of image  
messages specified in the settings to your mobile phone or e-mail address. Motion detection is then  
turned off. If you want to use motion detection again, send the SMS message 2 on [number of image  
messages (0-10)] to the Nokia Observation Camera.  
Note: Motion detection does not work if there are obstacles, such as windows or walls between  
the camera and the target.  
Note: The size of the image messages and possible network-related issues may affect the time  
in which the image messages are received.  
If the camera has detected motion, and you do not want it to send motion detection messages to  
anyone, you have 15 seconds to turn off motion detection by pressing the motion detection button on  
30  
Copyright©2003 Nokia. All rights reserved.  
 
   
the camera. You can configure the 15 second delay on the Automatic imaging tab, see page 12. If you  
press the motion detection button while the camera is sending an image, the camera sends the image  
first and then turns off motion detection.  
To turn off motion detection, send the SMS command 2 off to the Nokia Observation Camera.  
Using timed imaging  
To set the camera to capture images at defined intervals, send the SMS command 4 on hh:mm number  
to the Nokia Observation Camera. Replace hh:mm with the desired interval, for example 00:01, if you  
want the interval to be one minute, or 01:00, if you want the interval to be one hour. Replace number  
with the maximum number (0-10) of timed images you want to receive.  
Note:If you set 0 as the number of images, timed imaging remains on until you turn it off.  
Note: If you turn timed imaging on with SMS, the images are sent to the master user only.  
You can also set timed imaging on with PC Suite. With PC Suite you can also define how many timed  
images you want to receive before the timed imaging feature is turned off, see Automatic imaging  
tab on page 12.  
When you have set timed imaging on, the camera sends you the first image message after the first  
interval has passed.  
Note: The size of the image messages and possible network-related issues may affect the time  
in which the image messages are received.  
31  
Copyright©2003 Nokia. All rights reserved.  
 
 
Using the thermometer  
Note: Turn the thermometer up before using it. Do not use force. See Figure 2 on page 5.  
To check the current temperature in the camera premises, send the SMS command 3 to the Nokia  
Observation Camera.  
If you want the camera to send you a notification via SMS when the maximum or the minimum  
temperature is reached in the premises, send the SMS command 15 on minimum value maximum value  
to the Nokia Observation Camera (replace minimum value and maximum value with the desired  
values)  
Note: After the camera has sent you a notification on the reached temperature, you need to set  
the temperature limits again, if you want to continue using this function.  
If you want the camera to include temperature in the image messages, see Thermometer tab on page  
13.  
Using the audio connection  
Make a phone call to the Nokia Observation Camera and you can hear the voices in the premises of  
the camera. During the call, motion detection is disabled, and SMS commands are put on hold and  
executed after the call.  
Note: When the camera is sending images, it cannot answer phone calls.  
Note: Obey all local laws governing listening. Do not use this feature illegally.  
32  
Copyright©2003 Nokia. All rights reserved.  
 
   
Care and maintenance  
The Nokia Observation Camera is a product of superior design and craftsmanship and should be treated  
with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this  
product for many years.  
• Keep the camera and all its parts and accessories out of the reach of small children.  
• Keep the camera dry. Precipitation, humidity and all types of liquids or moisture can contain  
minerals that will corrode electronic circuits.  
• Do not use or store the camera in dusty, dirty areas. Its moving parts can be damaged.  
• Do not store the camera in hot areas. High temperatures can shorten the life of electronic devices,  
damage batteries, and warp or melt certain plastics.  
• Do not store the camera in cold areas. When it warms up (to its normal temperature), moisture can  
form inside, which may damage electronic circuit boards.  
• Do not attempt to open the camera. Non-expert handling may damage it.  
• Do not drop, knock or shake the camera. Rough handling can break internal circuit boards.  
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the camera.  
• Do not paint the camera. Paint can clog the moving parts and prevent proper operation.  
• Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications  
or attachments could damage the camera and may violate regulations governing radio devices.  
33  
Copyright©2003 Nokia. All rights reserved.  
 
 
All of the above suggestions apply equally to your camera or any enhancement. If any of them is not  
working properly, take it to your nearest qualified service facility. The personnel there will assist you  
and, if necessary, arrange for service.  
34  
Copyright©2003 Nokia. All rights reserved.  
 
Important safety information  
Traffic safety  
Don't install the camera in a vehicle. Do not use the camera or your mobile phone to control or configure  
the camera while driving; park the vehicle first. Do not place the camera on the passenger seat or where  
it can break loose in a collision or sudden stop.  
Remember road safety always comes first!  
Operating environment  
Remember to follow any special regulations in force in any area and always switch off your camera  
whenever it is forbidden to use it, or when it may cause interference or danger.  
Use the camera only in its normal operating positions.  
Electronic devices  
Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain  
electronic equipment may not be shielded against the RF signals from your camera.  
Vehicles  
RF signals may affect improperly installed or inadequately shielded electronic systems in motor  
vehicles (e.g. electronic fuel injection systems, electronic antiskid (anti-lock) braking systems,  
electronic speed control systems, air bag systems). Check with the manufacturer or its representative  
35  
Copyright©2003 Nokia. All rights reserved.  
 
 
regarding your vehicle. You should also consult the manufacturer of any equipment that has been  
added to your vehicle.  
Pacemakers  
Pacemaker manufacturers recommend that a minimum separation of 20 cm (6 inches) be maintained  
between a camera and a pacemaker to avoid potential interference with the pacemaker. These  
recommendations are consistent with the independent research by and recommendations of Wireless  
Technology Research. Persons with pacemakers:  
• Should always keep the camera more than 20 cm (6 inches) from their pacemaker when the camera  
is switched on;  
• If you have any reason to suspect that interference is taking place, switch off your camera imme-  
diately.  
Hearing aids  
Some observation cameras may interfere with some hearing aids. In the event of such interference,  
you may want to consult your service provider.  
Other medical devices  
Operation of any radio transmitting equipment, including cameras, may interfere with the  
functionality of inadequately protected medical devices. Consult a physician or the manufacturer of  
the medical device to determine if they are adequately shielded from external RF energy or if you have  
any questions. Switch off your camera in health care facilities when any regulations posted in these  
areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be  
sensitive to external RF energy.  
36  
Copyright©2003 Nokia. All rights reserved.  
 
Posted facilities  
Switch your camera off in any facility where posted notices so require.  
Potentially explosive atmospheres  
Switch off your camera when in any area with a potentially explosive atmosphere and obey all signs  
and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even  
death.  
Users are advised to switch off the camera when at a refuelling point (service station). Users are  
reminded of the need to observe restrictions on the use of radio equipment in fuel depots (fuel storage  
and distribution areas), chemical plants, or where blasting operations are in progress.  
Areas with a potentially explosive atmosphere are often but not always clearly marked. They include  
below deck on boats; chemical transfer or storage facilities; vehicles using liquified petroleum gas  
(such as propane or butane); areas where the air contains chemicals or particles, such as grain, dust  
or metal powders; and any other area where you would normally be advised to turn off your vehicle  
engine.  
Failure to observe these instructions may lead to suspension or denial of telephone services to the  
offender, or legal action or both.  
The Nokia Observation Camera, like any wireless device, operates using radio signals, wireless and  
landline networks, and user-programmed functions. Because of this, connections in all conditions  
cannot be guaranteed. Therefore you should never rely solely upon any wireless phone for essential  
communications (e.g. medical emergencies).  
37  
Copyright©2003 Nokia. All rights reserved.  
 
Technical specifications  
Supported operating systems  
PC Suite supports Windows 98/2000/NT/XP.  
Operating temperature  
-10...+50 degrees Celsius, 14...122 degrees  
Fahrenheit  
Lighting  
The camera captures colour images in normal  
lighting conditions. For low light conditions the  
camera includes an infared light source. Images  
captured with infrared light are black and  
white.  
The coverage area of the infrared light is  
approximately 3 metres.  
Focus area  
Resolution  
Minimum focus distance is 0.5 metres.  
High = 640 x 480 pixels  
Normal = 320 x 240 pixels  
Compact = 160 x 120 pixels  
Image format  
Viewing angle  
The image format is JPEG.  
The viewing angle is 58 degrees.  
38  
Copyright©2003 Nokia. All rights reserved.  
 
Motion detection coverage area  
The camera reacts to moving thermal radiation,  
and it detects an adult of average height  
approximately within 5 metres. Motion  
detection works also in the dark.  
Audio connection  
Humidity  
You can hear a normal human conversation  
from approximately 4 metres in indoor  
conditions.  
5...95% non condensing.  
39  
Copyright©2003 Nokia. All rights reserved.  
 

Abocom Network Card WMG2400 User Manual
Addonics Technologies Network Card ADU2N1G User Manual
AEG Freezer AGN71800F0 User Manual
Alliance Laundry Systems Washer HX18PVQM6 User Manual
AmbiCom GPS Receiver BT GPS User Manual
AMD Computer Hardware SC2200 User Manual
Atlantis Land Switch A04 H401 User Manual
Atlona TV Cables AT HD4 V11OSR User Manual
Banner Power Supply PSA 24 User Manual
BB Electronics Network Card TS W Family User Manual